DESCRIPTION:
A moisture tolerant, non-toxic, extremely durable epoxy with good chemical resistance. Water extended, clear epoxy with a special modified amine activator.
...Protects concrete
floor surfaces and reduces chalking.
This product sets faster than other epoxies
Reduces "downtime"
for the application.
Provides
quick turn-around time.
Used as the primer for the
base color coat decorative flooring system.
As a clear coat this product is excellent for warehouses, factories, clean rooms and food related industries.
Outstanding for ease of application and job clean up.
Quick set-up time
Excellent for areas of high traffic and where next day usage
is important. Sets in a short time and can be walked on in approximately 1 to 4 hours
depending on the humidity and temperature of
the surface coated.
Packaging
Kits are pre-measured in proper ratios and ready to use.
2 gallon kits and 10 gallon kits.
Pot life
long
pot life, minimum of 4 hours at 70ºF.
Temperature affects pot life.
Coverage
300 to 400 square feet
per coat, per gallon.
Coverage per gallon in two coats is
approximately 175 to 200 square feet.
Colors
Clear, slight amber tone.
* CUSTOM COLORS AVAILABLE
Advantages
ª Fast Set, Long Pot Life
ª Highly Durable
ª
Good Chemical Resistance
ª Superior Abrasion Resistance
ª Non-flammable
ª No unpleasant
or dangerous odors
ª Cleans up with water
ª Long pot life prior
to application
ª Tools clean up with water
ª Can be applied to moist
surfaces
ª No special equipment needed
ª
Meets USDA requirements
USDA
Meets the USDA requirementsfor intermittent food contact.
Food handling areas/floors
Warehouses & stores
Airplane hangars
Factories
Clean-rooms
Animal facilities
Machine shops
Laboratories and pathology rooms
Dust-proofing
Waterproofing
Preparation
The
surface shall be clean and free of old coating,
grease or any contaminants.
Clean the concrete surface to
produce a dust free, rough profile.
The surface may be slightly damp
prior to application.
Mixing
THOROUGHLY mix the A & B components using a drill motor and jiffy mixer.
Allow an induction time of about 15 minutes before using the product.
Additional Water
Not more than 10% water may be added.
Add water only after mixing.
Prime Coat
The
kit of A and B should bemixed together completely before making
the prime coat .
Thin with water only as needed for the application.
Application
Apply
at 40ºF to 125ºF and 5ºF above dew point.
May
be applied by brushes,trowels, rollers
and by airless spraying.
Dry film thickness - 2.0 to 5.0 mils per coat.
Multiple applications may be used to achieve desired film thickness.
When rolling,
apply the product in a direction 90
degrees to the last rolled application.
A short nap roller is used.
The product sets quickly,
for best results apply the color chips before the product begins to set.
Apply Aliphatic Top Coat only when the base
coat under the color chips is completely dry.
Drying time
Humidity and temperature will affect the length of time the coatings cure.
Normal drying time is between four and six hours, however, the prime coat may set and be dry to touch
quite quickly and depending on the temperature additional coats
may be dry to touch as soon as one
or two hours.
Always inspect and check the coated area before allowing traffic over the surface.
Full cure and chemical resistance developmentis approximately five to seven days
Most polymer products, i.e. epoxy, urethane, etc. complete full cross linking in this amount of time.
Clean-up
Soap
and water.
Temperature
Resistance up to 250ºF dry.
Finish:
Medium-High Gloss, texture will varydue to substrate.
Caution:
Flattening and minor color change may occur with extended exposure to sunlight.
